Got this to replace wornout funnel on perfectly good gas cans. Does the job. Has sufficient combinations to fit any can, from what I could tell. Replaced 3 differnt funnels from gas cans from many different generations, and all of them fit well and worked perfectly. The price leaves something to be desired, when you consider that this is just a bunch of plastic parts. However, given the outrageous price they want for new cans that have funnel that impossible to use, then these make sense. Overall quality is good and functionality is as advertised.
Verified purchase: Yes | Condition: New
Bought 2 of these from this vendor. Went to add one of them to one of my plastic gas can and the yellow cap that goes around the spout immediately cracked and is now worthless. No, this was not from over tightening. The cap had barely seated when it cracked. Luckily I had the 2nd one as a replacement, but am not left with a useless spout and a vendor who refuses to answer messages or do anything about the broken item. I see this as a manufacturer defect yet the vendor is unresponsive even after multiple attempts at contacting them. I have purchased a number of these spouts locally over the years and always had good luck with them. Not sure if it was just this particular spout or a downgrade in manufacturing quality. Either way, I am not out the money and have a useless spout. Bottom line: If you're going to buy one of these, DO NOT USE THIS VENDOR!Read full review
Verified purchase: Yes | Condition: New
I actually saw a video on YouTube that caught my attention to this product. I had two plastic gas cans I purchased about 7 years ago just before moving out here to the desert, and I was shocked and very dismayed at how quickly the inner workings of the filler spouts turned to garbage, making the entire thing almost unusable. Much to my delight, the video brought to my attention these replacement spouts that were available and I promptly ordered two of them. They attached very quickly and appear to form a tight seal, and though I've yet to actually fill the gas cans with gasoline, I'm sure they'll do just fine and I am very thankful I've salvaged what was originally an extremely poor design flaw in the original product and I therefore now have the use of my gas cans once again, and at a minuscule price compared to buying new gas cans. I do highly recommend this product! Thanks!!Read full review
Verified purchase: Yes | Condition: New
This spout is what makes these new (practically useless) gas cans work. This is the second time I have bought this spout and it continues to not disappoint. The 10050 model does away with the need for a funnel to put gas in a car because the tip will fit into the filler neck. But the real secret is the vent plug. That allows gas to flow freely by allowing air into the can from a source other than the spout itself. Just drill a 1/2 inch hole in the top of the can opposite the spout, clean out the shavings from inside the can (best done while can is dry), snap in the vent and it is ready to pour. I can empty a 5 gal can in about a minute with this spout and vent combo. Note: the 1/2 inch hole is best drilled with a step drill bit ... they are cheaper than a 1/2 inch twist drill bit and don't make as many shavings. You can find them at any hardware or parts store and big boxes ... and probably eBay too!Read full review
Verified purchase: Yes | Condition: New
Recommend them to anyone who hates fooling around with the idiotic mandated spouts on todays gas cans. I run thru 5 to 15 gallons of gas a months running my yard tractor, New spouts make it easy to fill gas tank with no spills something you can't do with the integral spouts on new cans. Suggest using a tubeless valve stem (sans Schrader valve) in place of the yellow button valves in the kit (Google process).
Verified purchase: Yes | Condition: New
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Best Selling in Dispensers & Accessories
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Save on Dispensers & Accessories