When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Flex Radio Systems Flex 5000A. Looks and works like new. Has Antenna tuner and 2nd Receiver options. Requires Fire Wire port on PC to use. Includes Quick start manual, Power and Firewire cable.
Content provided by:FlexRadio Systems Engineering
General
RxFrequencyRange:
10KHz- 60MHz
(Customer provided preselector or appropriately selected low pass filters required to eliminate images when used below 1.8MHz)
160 - 6 m (specified performance, Amateur bands only)
160 - 6 m (Amateur bands only)
Frequency Stability:
±0.5 ppm 32 °F to 122 °F (0 °C to +50 °C)
Ambient OperatingTemperatureRange:
14 °F to 122 °F (–10 °C to +50 °C)
Emission Modes:
A1A (CW), A3E (AM), J3E (LSB,USB), F3E (FM),
F1B (RTTY), F1D (PACKET), F2D (PACKET)
Frequency Steps:
1Hz minimum
AntennaImpedance:
50 Ohms, unbalanced
6 - 1000 Ohms, unbalanced (With Optional Tuner ON, 160 - 10 m Amateur bands)
16 - 150 Ohms, unbalanced (With Optional Tuner ON, 6 m Amateur band)
Power Consumption:
Rx1.5A (typ.);Tx(100 W) 25A (max.)
Supply Voltage:
DC: DC 13.8V± 10%
Maximum Interconnect Cable Length:
Firewire- 10 feet (3m),
No restriction on DC power cable within voltage tolerance limits underload.
NOTE: Necessary to minimizeRFIradiation from the cables attached to the radio
1 snap on ferrite bead on DC power cable,
2 snap on ferrite beads onFireWire® cable
1 snap on ferrite bead on FlexWire™ cable
All beads to be located adjacent to rear panel of radio.
FLEX-5000A Dimensions:
(WxHxD): 9.3” x 8.7” x 13.8” (23.5 cm x 22.1 cm x 31.5 cm)
FLEX-5000A Weight:
(approx.): 13 lbs (5.9 kg)
Transmitter
Power Output:
1 - 100 wattsPEPCWandSSB(2 - 25 wattsAMcarrier)
28MHzIFPower Output:
0 dBm (1.0 milliwatt)
Emission Modes Types:
A1A (CWU, CWL), J3E (USB,LSB), A3E (AM), F3E (FM), DIGITAL
Spurious andHarmonicRadiation:
Better than –55dB(160 - 10m Amateur bands)
Better than –65dB(6m Amateur band)
SSBCarrierSuppression:
At least 55dBbelow peak output
Undesired Sideband Suppression:
At least 60dBbelow peak output
Audio Response(SSB):
90 Hz @ -3dB / flat to upper limit set by software,Software EQ optional
3rd-orderIMD:
Better than –33dBbelowPEP@14.2MHz100 wattsPEP
9th-orderIMD:
Better than –54dBbelowPEP@14.2MHz100 wattsPEP
ImageRejection:
88dB
MicrophoneImpedance:
600 Ohms (200 to 10k Ω)
Balanced Line InImpedance:
600 Ohms (200 to 10k Ω)
Receiver
Circuit Type:
Direct conversion, lowIF
Intermediate Frequency:
Software selectable from DC to 20KHz
Sensitivity(preamp off/on):
1.3/0.3 µV at 14MHz
MDS (preamp off/on):
-123 dBm/-133 dBm in 500 Hz BW
IMDDR3 (dynamic range):
99dBat 14MHzwith preamp off or off at 2kHzor less tone spacing
IP3:
+30 dBm at 14MHzwith preamp off at 2kHzor less tone spacing (S5 IM3 test method)
+39 dBm at 14MHzwith preamp off at 2kHzor less tone spacing (ARRLtest method)
IP2:
+63 dBm at 14MHzwith preamp off at 2kHzor less tone spacing (ARRLtest method)
CW500 Hz –6/-60dB: 500/640
SSB2.4kHz–6/-60dB: 2.39/2.54
AM6.6kHz–6/-60dB: 6.60/6.74
ImageRejection:
70dBor better (160 - 6m Amateur bands)
Certifications:
CE Declaration of Conformity (25-August-2007) for the FLEX-5000A
CE Declaration of Conformity (23-August-2008) for the FLEX-5000A with RX2 (secondreceiver)